VOLTAGE FALL REPAIR SIMULATION OF PT PLN (PERSERO) ULP BIMA KOTA VOLTAGE FALL USING ETAP 12.6.0 APPLICATION

Authors

  • Choiruzzad Fahri Universitas Teknologi Sumbawa
  • Paris Ali Topan Universitas Teknologi Sumbawa
  • Masyitah Aulia Universitas Teknologi Sumbawa
  • Nova Aryanto Universitas Teknologi Sumbawa

DOI:

https://doi.org/10.51401/altron.v2i02.2251

Keywords:

Drop Voltage, ETAP 12.6.0, Feeder Load Break, Saving kWh

Abstract

According to Law no. 30 of 2009 article 28 concerning electricity, that holders of business
licenses for the supply of electricity are required to provide electricity that meets the applicable
reliability quality standards. In the electric power system, especially in the 20 kV Medium
Voltage Network, there is a radial primary distribution feeder on the PT PLN (Persero) UP3
Bima ULP Bima Kota network, namely Rontu Feeder. The Rontu feeder distributes electrical
energy to household consumers and business consumers in the Raba District and parts of the
West Rasanae District, Bima City. With a feeder length of 49 kms and a peak night load of
3361 kW. The measurement of the end voltage in the field was 18.92 kV which caused a drop
in voltage value of 5.42% so that it did not comply with the SPLN standard No. 72 of 1987,
which regulates the value of the voltage drop at SUTM 5% of its working voltage. This thesis discusses the steps to rectify the voltage with the simulated load breaking method in the
application. In this thesis using the ETAP 12.6.0 application the simulation will be carried out
with two conditions, namely: 1) the existing condition of the Rontu Feeder, and 2) the condition
of the Rontu Feeder broken down by the feeder load. The simulation results show that the
voltage correction method by breaking the load can reduce the voltage drop in the Rontu
Feeder by 78.70% from 18.92 kV to 19.77 kV

References

Amu. Ilham, “Kajian Kelayakan Operasi Pecah Beban Penyulang Beta (SJ-2) untuk Kehandalan Sistem Kelistrikan Kota

Bitung”, Gorontalo: Universitas Negeri Gorontalo, 2019.

Kamalia. Dhiva Feneranda, “Analisis Susut Energi (Losses) Jaringan Tegangan Menengah (20KV) di PT PLN (Persero)

Rayon Klakah Area Jember”, Makassar: Fakultas Teknik Elektro Universitas Muhammadiyah Makassar, 2018.

M. Mujiburrahman, Joko, dan B. Suprianto, “Analisis Tegangan Jatuh (Drop Voltage) pada Unit Boiler di PPSDM Migas

Cepu Menggunakan ETAP 12.6.0”, J. Nas. Tek. Elektro, 2021.

Nugroho. Aditya Adi, “Analisis Pengaruh Penambahan Penyulang MSR 13 Untuk Mengatasi Jatuh Tegangan dan Rugi

Daya pada Penyulang SRN 03”, Surakarta: Fakultas Tenik Universitas Muhammadiyah Surakarta, 2020.

Pemerintah Indonesia, Undang-Undang Nomor 30 tahun 2009, Jakarta: Sekretariat Negara, 2009.

Pramono. Tri Joko, “Analisis Drop Tegangan Pada Jaringan Tegangan Menengah Dengan Menggunakan Simulasi

Program ETAP”, Jakarta: Fakultas Ketenagalistrikan dan Energi Terbarukan IT PLN, 2019.

PT PLN (Persero), Buku 1 Kriteria Disain Enjinering Kontruksi Jaringan Distribusi Tenaga Listrik, Jakarta Selatan: PT

PLN (Persero), 2010.

PT PLN (Persero), Buku 3 Standar Konstruksi Jaringan Tegangan Rendah Tenaga Listrik, Jakarta Selatan: PT PLN

(Persero), 2010.

PT PLN (Persero), Buku 4 Standar Konstruksi Gardu Distribusi dan Gardu Hubung Tenaga Listrik, Jakarta Selatan: PT

PLN (Persero), 2010.

PT PLN (Persero), Buku 5 Standar Konstruksi Jaringan Tegangan Menengah Tenaga Listrik, Jakarta Selatan: PT PLN

(Persero), 2010.

Putri. Dewi Maylani, “Upaya Perbaikan Jatuh Tegangan pada Penyulang Anggur dengan Metode Pecah Beban di ULP

Cikarang Kota”. Jakarta: Fakultas Ketenagalistrikan dan Energi Terbarukan IT PLN, 2020.

PT PLN (Persero), SPLN 59:1985, Jakarta: PT PLN (Persero),1985.

PT PLN (Persero), SPLN 72:1987, Jakarta: PT PLN (Persero),1987.

Suza. M. Gian, “Perbaikan Tegangan Penyulang melati dengan Metode Pecah Beban pada PT PLN (Persero) Bangkinang”,

Jakarta: Fakultas Ketenagalistrikan dan Energi Terbarukan IT PLN, 2021.

Wahyu. Asmar, “Analisa Perbaikan Susut Teknis dan Susut Tegangan pada Penyulang KB5 di PLN Rayon Koba untuk

Perbaikan Tegangan dan Susut”, Bangka Belitung: Universitas Bangka Belitung, 2017.

Winardi. Bambang, “Analisa Perbaikan Susut Teknis Dan Susut Tegangan Pada Penyulang Kls 06 di GI Kalisari Dengan

Menggunakan Software ETAP 7.5.0”.

Published

2023-08-09

How to Cite

Fahri, C., Topan, P. A., Aulia, M., & Aryanto, N. . (2023). VOLTAGE FALL REPAIR SIMULATION OF PT PLN (PERSERO) ULP BIMA KOTA VOLTAGE FALL USING ETAP 12.6.0 APPLICATION. Journal Altron; Journal of Electronics, Science & Energy Systems, 2(02), 173-179. https://doi.org/10.51401/altron.v2i02.2251

Most read articles by the same author(s)

1 2 3 > >>